Bradite
ME53 Fastrac Enamel Gloss Green (Ready Mixed) 1L

BL04362015N
£19.34 inc. VAT
Trade customer? - log in to get your prices. close

Tell us where you are to check stock for Click & Collect:

A single pack fast drying, high gloss finishing coating for metal.
ME53 Fastrac Enamel Gloss Green (Ready Mixed)
Share...

In detail

Bradite ME53 Fastrac Enamel Gloss is a single pack fast drying, high gloss finishing coating, containing rust inhibiting pigmentation for extra protection. 

Fastrac Enamel Gloss has a tough, flexible finish, excellent protective properties against corrosion and is resistant to spillage of mild chemicals, oils and hydrocarbons. 

Suitable as a one or two coat finish, or as part of a fast drying protective system for steel or suitably primed non ferrous metals.

Touch dry in 1-4 hours and recoatable after 12-24 hours.

Size
1L 
Application Methods
Airless Spray, Brush, HVLP Spray, Roller
Coverage
Up to 14sq/m per litre 
VOC level
High 
Thinning
Bradite TW35 
Touch dry
1-4 hours 
Recoatable
12-24 hours 
Scrubbability
Washable 
Colour
Green 
Finish
Gloss 
Cleanup
Bradite TW35 

Additional information

Bradite paints and coatings meet the highest quality and performance standards in the most demanding environments. To obtain satisfactory results you should ensure you know the best way to use the product. Free advice is available upon request from Bradite Paints and its distributors. General advice given below does not constitute a specification.

Preparation

Correct preparation is vital to ensure you obtain the full benefits from Bradite Fastrac ME53 Full Gloss and SE53 Satin.

Application

  • By brush, roller or spray (please refer to data sheet for spraying information).
  • Apply one or two further full coats as required.
  • Bradite Fastrac ME53 and SE53 will be touch dry in
  • 2 hours at 20°C, but a minimum of 16 hours should be allowed before over coating.
  • Touch dry in 2 hours, recoat 16 hours with full cure after 7 days
  • The theoretical (maximum) spreading rate is 13 square metres per litre per coat. Loss factors will apply in practice.
  • Tools should be cleaned with white spirit after use.
  • Thinning with TW35.

New and unpainted steel:

  • High pressure water cleaning to remove all loose salts and other contaminants.
  • Degrease using a suitable detergent, BRADITE TD39, with scrubbing plus high pressure water cleaning to remove any oil contamination not removed by high pressure cleaning alone, rinse with clean water and allow to dry.
  • Mechanically or manually prepared steel to a clean metallic finish, SIS-St 3 minimum.
  • Substrate to be dry, clean and free of contamination and dust free prior to coating.

Existing coatings:

  • Jet wash to remove all loose and flaking paint, salts and other contaminants.
  • Degrease using Bradite TD39 diluted with up to 9 parts of warm water and scrubbing to remove any oil contamination not removed with jet washing alone, rinse with clean water and allow to dry.
  • Existing coatings should be well adhered with all edges tight and well feathered.
  • Bare or rusted steel should be manually or mechanically abraded to a clean metallic finish (SIS-St 3).
  • Substrate should be clean, dust free and dry before application.
  • Spot prime with correct primer.
  • Galvanised steel, Aluminium and other non-ferrous steels should be roughened or lightly abraded and treated with Bradite Barrier Primer EU96 or Bradite Sorted WP45.
  • New bright galvanised should be degreased and treated with Bradite TM38 pre-treatment for galvanised steel