Sadolin
Superdec Opaque Wood Protection Satin Super White 5L

HA5725605F
Highly flexible coating for exterior doors, windows and cladding. Water-based. 10 years protection.
Share...

In detail

Sadolin Superdec Opaque is a highly flexible water-based coating for exterior wood.

Recommended for doors, windows and cladding.

Ideal where a complete change of colour is required and helps to treat uneven, weathered surfaces.

The flexible coating expands and contracts with the wood, resisting cracking, flaking and peeling.

It can be applied to new and previously stained or painted surfaces and is ideal for a complete change in colour or hiding timber blemishes.

Application is recommended by synthetic brush with coverage up to 15sq/m per litre.

Touch dry in 1 hour and recoatable in 16 hours

2 coats are recommended.

Size
5L 
Application Methods
Brush
Coverage
Up to 15sq/m per litre 
VOC level
Low 
Thinning
Not recommended 
Touch dry
1-4 hours 
Recoatable
12-24 hours 
Suitable for...
Exterior use 
Scrubbability
Washable 
Lifespan
Up to 10 years 
Colour
Super White 
Colour type
Ready Mixed 
Finish
Satin 
Cleanup
Water & Detergent 
Base
Water-Based 

Additional information

Sadolin Superdec Satin is the ultimate in opaque wood protection. It's unique, water borne formulation is self priming and undercoating, penetrating into the wood for optimum protection. Sadolin Superdec is extremely flexible, contracting and expanding with the wood, and therefore resisting cracking, peeling and flaking. It can be applied to new and previously painted or stained surfaces and is ideal for hiding timber blemishes, or when a complete change of colour is required.

Preparation

We recommend a trial application before you start. The final colour and coverage will depend on the original colour and condition of the wood and the number of coats applied. Crown Paints is not liable for costs caused as a result of an incorrect colour being applied or failure to follow the manufacturer's directions.

  • Low Grade or Resinous Timber: Treatment of resinous knots is recommended prior to application of Sadolin Superdec by drilling out and filling or the application of an appropriate blocking primer.
  • New or Bare Wood: Timber exposed for 4 weeks or more will require sanding to a clean, sound surface. If the wood is oily thoroughly degrease the timber surface with a suitable solvent eg. Methylated spirits. If required, treat with Sadolin Quick Dry Wood Preserver. Fill small holes with Sadolin Woodfiller. Sand in the direction of the grain to a smooth surface.
  • Previously Painted or Varnished Surfaces: Strip back and treat as new wood
  • Previously Painted or Woodstained Surfaces: Ensure surfaces to be treated are clean, dry and free from dust, grease, wax, resin and other timber extractives. Remove any loose or flaking coating using a scraper and/or abrasive paper. Remove any grey, denatured timber, and sand the sound coating with abrasive paper to provide an adequate key. Do not use wire wool. Ensure existing sound coated areas are cleaned with a mild detergent, warm water and rinsed off with clean water. Allow to dry. Strip surfaces in poor condition bare and treat as new. As with all coatings preparation is key and poor preparation will result in poor coating performance.

Application

  • Always intermix packs to ensure colour consistency.
  • Ensure surfaces to be coated are clean and dry.
  • Stir well before and during application.
  • Do not apply in damp conditions, when rain is imminent, or at temperatures below 80°C or above 25C.
  • For best results use a good quality synthetic bristle brush.
  • Avoid over brushing as this will result in brush marks.
  • Sand lightly between coats if there is any raised grain.
  • New work requires a three coat application.
  • Maintenance may require two or three coats depending on the amount of weathering that has occurred.